Airplanes * | Sebart Mini Avanti S V3 90Mm Jet 1,36M Arf (White/Blue)

More Info

Sebart Mini Avanti S 90Mm Jet 1,36M Arf (White/Blue)

Sebart Fiberglass Mini Avanti S Jet With Electric Retracts, Gear Doors And Corresponding Servos And Sequencer, As Well As All Accessories. Designed For 90Mm Edf Or P20-30N Jet Turbine.

The Mini Avanti S Arf Jet Was Designed By The Italian Aerobatic Champion, Sebastiano Silvestri. This Sport Arf Jet Model Design Is Based On The Bae Hawk Real Aircraft Design And Enhanced By Adding The Ultimate Aerodynamics Principals Of The Modern Fai Pattern Models And Using The 15 Years Experience In Flying Jets Of Seba…. The Result Is Outstanding!

This Innovative Design Combined With A Lightweight Structure, The Full Composite Fiberglass Fuselage And All Wood Airframe Wings And Stabs, Give The Mini Avanti S New Levels Of Precision And Smoothness At Any Airspeed And Flight Conditions.

We Are Available To Discuss With You The Best Edf Setting For This Model. You Can Also Select One Of The Combos With Edf And Esc Available On The Store.

Different Parts And Options Available To Complete The Kit.

Nota: Pictures Of The Livery For Information Only. The Pictures Of Avanti S Livery White/Yellow Are Not Yet Available.

Features

• Painted Fiberglass Fuselage
• Wings And Stabilizers In Balsa Covered With Oracover
• Suitable For P20-30 Jet Turbine With The “Turbine Kit”
• Factory Installed Electric Retract Landing GearnWith Doors Sequencer Included

Technical Specifications

• Wing Span: 1360Mm / 53,54 In
• Length: 1420Mm / 55,9 In
• Wing Area: 38Dm / 589 Sq In
• Weight (Edf Version): 2.9Kg / 6,393 Lb (Without Battery)
• Flying Weight (Version Edf): Approx. 3.8Kg / 8,377 Lb (With 5800Mah 6S Lipo)
• Weight (Turbine Jet Version): 3.05Kg / 6,724 Lb (Empty Tank And No Turbine Battery)
• Flying Weight (Turbine Jet Version): 3.75Kg / 8,267 Lb (Battery + 650Cc Tank Fuel)

Note: The Factory-Installed Electric Retracts, Nose Gear Door Servos And Steering Servo Can Not Be Powered By More Than 6.0V. If You Intend To Use Hv Servos For The Control Surfaces And Use A 2S 7.4V Lipo Pack, A Voltage Regulator Will Be Required To Prevent Damage To The Sequencer.

Includes

• Sebart Mini Avanti S 90Mm Jet 1,36M Arf (White/Blue)
• Pre-Installed Electric Retracts, Gear Doors And Their 3 Corresponding Servos And Sequencer.

Requires

• 90Mm Edf And Esc
• Minimum 6 Channels Radio And Receiver
• 7X Sub Micro Servos (1X Rudder, 2X Elevator, 2X Ailerons, 2X Flaps), Ie: Spektrum A4030
• 5000-5800 Mah 35-50C Lipo Battery (8 To 10S)
• Lipo Battery Charger
• Estimated Build Time Is 2 Hours

Can Also Be Equiped With A P20-30 Jet Turbine With The “Turbine Kit” (Available On Demand)

Recommended Edf Power Set Up

• Jp Hobby 90Mm Or Jetfan 90V2

Recommended Turbine Power Set Up

• P20-30N Jet Turbine With The “Turbine Kit” (Available On That Store)

Data Sheet